英文字典中文字典


英文字典中文字典51ZiDian.com



中文字典辞典   英文字典 a   b   c   d   e   f   g   h   i   j   k   l   m   n   o   p   q   r   s   t   u   v   w   x   y   z       







请输入英文单字，中文词皆可：


请选择你想看的字典辞典：
单词字典翻译
344326查看　344326　在百度字典中的解释百度英翻中〔查看〕
344326查看　344326　在Google字典中的解释Google英翻中〔查看〕
344326查看　344326　在Yahoo字典中的解释Yahoo英翻中〔查看〕

安装中文字典英文字典查询工具!


中文字典英文字典工具:
选择颜色:
输入中英文单字

































































英文字典中文字典相关资料:


  • Axes - Tools and Tool Making - Bladesmiths Forum Board
    Axe: 350, 450, 650g, blade 7, 8, 11cm Nice set Assume these are punch and drift of mild steel with a high carbon steel bit forge welded in? If so can you share what stock size you used? Edited April 4, 2016 by Dan Hertzson
  • Warping - Beginners Place - Bladesmiths Forum Board
    Ok, so warping has never really been a big concern for me I've never had a knife warp all too much during a quench or any other time for that matter However, something quite strange happened to one of the knives I was working on last night I previously thought that warping only occurred duri
  • Was chilly today : ( - Photography - Bladesmiths Forum Board
    Let not the swords of good and free men be reforged into plowshares, but may they rest in a place of honor; ready, well oiled and God willing unused For if the price of peace becomes licking the boots of tyrants, then "To Arms!" I say, and may the fortunes of war smile upon patriots
  • Replacement steel question - Hot Work - Bladesmiths Forum Board
    This is probably going to sound like a really stupid question but I need to replace the steel on my 'new' blower forge since it is older and seems to be crumbling around the edges when I touch it What would be a good steel with high heat resistance I can replace it with I dont know a while lot
  • makers mark - Show and Tell - Bladesmiths Forum Board
    I'm having a hard time figuring out my maker's mark What is better for a blade, having your name initials or a symbol or figure? any suggestions? then there is the question of whether to punch it hot or cold or electro-etch Also, if I make a punch and cut out the final idea, what steel should
  • not a knife - Show and Tell - Bladesmiths Forum Board
    hey all, just wanted to show what i've been up to now that i'm out of acetaline for a while haha i've been making torcs and chainmaille out of rebar tie, which i'm pretty happy about
  • Quench Tank Ideas - Hot Work - Bladesmiths Forum Board
    You do not want to quench the handle tangs, so an edge quench in the goop with the handle tangs hanging down might work IF you use a steel that hardens well in goop, which limits you to an alloy slow quench steel like 5160 or O-1
  • Tokugawa_Sensei - Bladesmiths Forum Board
    Thanks for the websites The first one makes sense Now wat r the tools to make them and where can I buy them at
  • Soldering Silver - Hot Work - Bladesmiths Forum Board
    So I'm trying to solder (butt end) a couple silver rings, 1mm thick, Sterling, using "easy" silver solder I cleaned my area, applied a thin layer of paste flux, cut a small thin section of solder and laid it at the joint - and nothing desirable happened when I applied heat in the form of a swirl
  • Anvil identification - Beginners Place - Bladesmiths Forum Board
    Hello all I am new to this forum as well as knife making I'm getting all the things I need to get started slowly I just got my anvil this past weekend from New York I have tried all the tricks I can think of to pull any maker's marks off the side, but I'm afraid it is too far gone I tried fl





中文字典-英文字典  2005-2009